Giúp bạn đến shop nhanh nhất có thể
(0 khách hàng Hỏi đáp và tư vấn)
| Xuất xứ |
|
DBX 1066
JBL
12 tháng
chiếc
Mới 100%
Còn hàng
>Giá chưa bao gồm VAT
Mua Ngay
Giao hàng tận nơi hoặc đến Showroom xem hàng
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Input Type | Electronically balanced/unbalanced, RF filtered |
| Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm |
| Max Input | > +24 dBu balanced or unbalanced |
| CMRR | Typically >50 dB at 1 kHz |
| Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Output Type | Servo-balanced/unbalanced, RF filtered |
| Output Impedance | Balanced 120 Ohm, unbalanced 60 Ohm |
| Max Output | > +21 dBm balanced, > +20 dBm unbalanced |
| Sidechain Input Connector | 1/4" Unbalanced (Tip-Sleeve) |
| Sidechain Input Type | Unbalanced, RF filtered |
| Sidechain Impedance | >10 kOhm |
| Sidechain Max Input Level | >+24 dBu |
| Sidechain Output Connector | 1/4" Balanced TRS (tip hot) |
| Sidechain Output Type | Impedance balanced, RF filtered |
| Sidechain Output Impedance | Balanced 2 kOhm, unbalanced 1 kOhm |
| Sidechain Max Output Level | >+21 dBu balanced or unbalanced |
| Bandwidth | 20 Hz to 20 kHz, +0/0.5 dB |
| Frequency Response | 0.35 Hz to 90 kHz, +0/-3 dB |
| Noise | < -95 dBu, unweighted, 22 kHz measurement bandwidth |
| Dynamic Range | > 118dB, unweighted |
| THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), < 0.1% any amount of compression up to 40 dB, 1 kHz |
| IMD | < 0.1% SMPTE |
| Interchannel Crosstalk | < -80 dB 20Hz to 20 kHz |
| Stereo Coupling | True RMS Power Summing |
| Compressor Threshold Range | -40 dBu to +20 dBu |
| Compressor Ratio | 1:1 to infinity:1 |
| Compressor Threshold Characteristic | Selectable OverEasy® or hard knee |
| Compressor Attack/Release Characteristic | AutoDynamic™ |
| Compressor Attack/Release Modes | Selectable Manual or Auto |
| Compressor Manual Attack Time | Scalable program-dependent |
| Compressor Manual Release Time | Scalable program-dependent |
| Compressor Auto Attack Time | Program-dependent |
| Compressor Auto Release Time | Program-dependent |
| Compressor Output Gain | -20 to +20 dB |
| Limiter Threshold Range | +4 dBu to +24 dBu (off) |
| Limiter Ratio | infinity:1 |
| Limiter Type | PeakStopPlus® two-stage limiter |
| Limiter Stage 1 | PeakStop® brickwall limiter |
| Limiter Stage 1 Attack Time | Zero |
| Limiter Stage 1 Release Time | Zero |
| Limiter Stage 2 | Predictive intelligent program limiter |
| Limiter Stage 2 Attack Time | Program-dependent |
| Limiter Stage 2 Release Time | Program-dependent |
| Expander/Gate Threshold Range | Off to +15dBu |
| Expander/Gate Ratio | 1:1 to 30:1 |
| Expander/Gate Attack Time | < 100 µsec |
| Expander/Gate Release Time | Program-dependent |
| SC Ext. Switch | Routes the external sidechain input signal to the detector |
| SC Mon. Switch | Routes the sidechain signal to the output, interrupting the normal audio |
| OverEasy® Switch | Activates the OverEasy compression function |
| Countour Switch | Activates the frequency-dependent detector function |
| Auto Switch | Activates automatic program-dependent attack and release times, disabling the manual Attack and Release controls |
| I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter |
| Bypass Switch | Activates the direct input-to-output hard-wire relay bypass. Relay automatically hard-wire bypasses unit at power-down and provides a power-on delay of 1.5 sec. |
| Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneoulsy for both input and output levels |
| ST Link Switch | Link both channels for stereo operation. Channel One becomes the master |
| Gain Reduction Meter | 12-segment LED bar graph at 1, 2, 4, 6, 9, 12, 15, 18, 21, 24, 27 and 30 dB |
| I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu |
| Compressor Threshold Meter | 3-segment LED bar graph at Below (-), OverEasy and Above (+) |
| Expander/Gate Threshold Meter | 2-segment LED bar graph at Below (-) and Above (+) |
| Limiter Threshold Meter | 1 LED to indicate PeakStopPlus™ limiting |
| Function Switches | LED indicator for each front-panel switch |
| Output Transformer Options | Jensen® JT-123-dbx or JT-11-dbx, BCI RE-123-dbx or RE-11-dbx |
| Operating Voltage | 100-120 VAC 50/60 Hz 200-240 VAC 50/60 Hz |
| Power Consumption | 20 Watts |
| Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T |
| Power Connector | IEC receptacle |
| Dimensions | 1.75"Hx19"Wx9"D (4.4cmx48.3cmx20.1cm) |
| 设备重量 | 5.1 lbs. (2.3 kg) |
| Shipping Weight | 7.5 lbs. (3.4 kg) |
Ampli DBX 1066 dbx mới VCA. Phát triển đặc biệt cho 1066, 1046 và các sản phẩm dòng khác 10 tới, VCA cách mạng này tự hào có các đặc điểm phạm vi năng động tuyệt vời trong khi vẫn duy trì sự biến dạng rất thấp và đặc điểm tiếng ồn gần như vô hạn. Điểm mấu chốt là: một VCA mới làm việc cùng với thiết kế đẳng cấp thế giới làm cho dbx1066 thực hiện tốt hơn so với máy nén khí bán cho hàng trăm người khác.
=>> Xem thêm: Compressor DBX 1046
Trong cơ sở phòng thu phát sóng, hoặc trên đường với một PAhệ thống, 1066 là thiết kế cho các hoạt động hoàn toàn đơn giản. 1066 cho phép bạn để loại bỏ tín hiệu không mong muốn, linh hoạt kiểm soát được tín hiệu tổng thể, và bảo vệ kết hợp tổng thể của bạn trong mono kép hoặc hoạt động âm thanh nổi.
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Input Type | Electronically balanced/unbalanced, RF filtered |
| Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm |
| Max Input | > +24 dBu balanced or unbalanced |
| CMRR | Typically >50 dB at 1 kHz |
| Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Output Type | Servo-balanced/unbalanced, RF filtered |
| Output Impedance | Balanced 120 Ohm, unbalanced 60 Ohm |
| Max Output | > +21 dBm balanced, > +20 dBm unbalanced |
| Sidechain Input Connector | 1/4" Unbalanced (Tip-Sleeve) |
| Sidechain Input Type | Unbalanced, RF filtered |
| Sidechain Impedance | >10 kOhm |
| Sidechain Max Input Level | >+24 dBu |
| Sidechain Output Connector | 1/4" Balanced TRS (tip hot) |
| Sidechain Output Type | Impedance balanced, RF filtered |
| Sidechain Output Impedance | Balanced 2 kOhm, unbalanced 1 kOhm |
| Sidechain Max Output Level | >+21 dBu balanced or unbalanced |
| Bandwidth | 20 Hz to 20 kHz, +0/0.5 dB |
| Frequency Response | 0.35 Hz to 90 kHz, +0/-3 dB |
| Noise | < -95 dBu, unweighted, 22 kHz measurement bandwidth |
| Dynamic Range | > 118dB, unweighted |
| THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), < 0.1% any amount of compression up to 40 dB, 1 kHz |
| IMD | < 0.1% SMPTE |
| Interchannel Crosstalk | < -80 dB 20Hz to 20 kHz |
| Stereo Coupling | True RMS Power Summing |
| Compressor Threshold Range | -40 dBu to +20 dBu |
| Compressor Ratio | 1:1 to infinity:1 |
| Compressor Threshold Characteristic | Selectable OverEasy® or hard knee |
| Compressor Attack/Release Characteristic | AutoDynamic™ |
| Compressor Attack/Release Modes | Selectable Manual or Auto |
| Compressor Manual Attack Time | Scalable program-dependent |
| Compressor Manual Release Time | Scalable program-dependent |
| Compressor Auto Attack Time | Program-dependent |
| Compressor Auto Release Time | Program-dependent |
| Compressor Output Gain | -20 to +20 dB |
| Limiter Threshold Range | +4 dBu to +24 dBu (off) |
| Limiter Ratio | infinity:1 |
| Limiter Type | PeakStopPlus® two-stage limiter |
| Limiter Stage 1 | PeakStop® brickwall limiter |
| Limiter Stage 1 Attack Time | Zero |
| Limiter Stage 1 Release Time | Zero |
| Limiter Stage 2 | Predictive intelligent program limiter |
| Limiter Stage 2 Attack Time | Program-dependent |
| Limiter Stage 2 Release Time | Program-dependent |
| Expander/Gate Threshold Range | Off to +15dBu |
| Expander/Gate Ratio | 1:1 to 30:1 |
| Expander/Gate Attack Time | < 100 µsec |
| Expander/Gate Release Time | Program-dependent |
| SC Ext. Switch | Routes the external sidechain input signal to the detector |
| SC Mon. Switch | Routes the sidechain signal to the output, interrupting the normal audio |
| OverEasy® Switch | Activates the OverEasy compression function |
| Countour Switch | Activates the frequency-dependent detector function |
| Auto Switch | Activates automatic program-dependent attack and release times, disabling the manual Attack and Release controls |
| I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter |
| Bypass Switch | Activates the direct input-to-output hard-wire relay bypass. Relay automatically hard-wire bypasses unit at power-down and provides a power-on delay of 1.5 sec. |
| Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneoulsy for both input and output levels |
| ST Link Switch | Link both channels for stereo operation. Channel One becomes the master |
| Gain Reduction Meter | 12-segment LED bar graph at 1, 2, 4, 6, 9, 12, 15, 18, 21, 24, 27 and 30 dB |
| I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu |
| Compressor Threshold Meter | 3-segment LED bar graph at Below (-), OverEasy and Above (+) |
| Expander/Gate Threshold Meter | 2-segment LED bar graph at Below (-) and Above (+) |
| Limiter Threshold Meter | 1 LED to indicate PeakStopPlus™ limiting |
| Function Switches | LED indicator for each front-panel switch |
| Output Transformer Options | Jensen® JT-123-dbx or JT-11-dbx, BCI RE-123-dbx or RE-11-dbx |
| Operating Voltage | 100-120 VAC 50/60 Hz 200-240 VAC 50/60 Hz |
| Power Consumption | 20 Watts |
| Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T |
| Power Connector | IEC receptacle |
| Dimensions | 1.75"Hx19"Wx9"D (4.4cmx48.3cmx20.1cm) |
| 设备重量 | 5.1 lbs. (2.3 kg) |
| Shipping Weight | 7.5 lbs. (3.4 kg) |
Âm Thanh Sân Khấu một trong những nhà cung cấp thiết bị âm thanh hàng đầu tại Việt Nam. Chúng tôi chuyên nhập khẩu và bán ra thị trường âm thanh tại Việt Nam những dòng sản phẩm âm thanh hội trường, âm thanh sân khấu, những thiết bị âm thanh dùng trong dàn karaoke chuyên nghiệp, equalizer dbx.. 100% chính hãng, chất lượng sản phẩm tốt nhất, giá cả cạnh tranh nhất trên thị trường âm thanh Việt Nam.
Với những thương hiệu âm thanh hàng đầu thế giới như JBL, Yamaha, Behringer, Soundking... tất cả những dòng sản phẩm bán ra thị trường đều được chúng tôi cam kết bảo hành chính hãng đầy đủ các phụ kiện, team, phiếu bảo hành theo từng sản phẩm.
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Input Type | Electronically balanced/unbalanced, RF filtered |
| Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm |
| Max Input | > +24 dBu balanced or unbalanced |
| CMRR | Typically >50 dB at 1 kHz |
| Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Output Type | Servo-balanced/unbalanced, RF filtered |
| Output Impedance | Balanced 120 Ohm, unbalanced 60 Ohm |
| Max Output | > +21 dBm balanced, > +20 dBm unbalanced |
| Sidechain Input Connector | 1/4" Unbalanced (Tip-Sleeve) |
| Sidechain Input Type | Unbalanced, RF filtered |
| Sidechain Impedance | >10 kOhm |
| Sidechain Max Input Level | >+24 dBu |
| Sidechain Output Connector | 1/4" Balanced TRS (tip hot) |
| Sidechain Output Type | Impedance balanced, RF filtered |
| Sidechain Output Impedance | Balanced 2 kOhm, unbalanced 1 kOhm |
| Sidechain Max Output Level | >+21 dBu balanced or unbalanced |
| Bandwidth | 20 Hz to 20 kHz, +0/0.5 dB |
| Frequency Response | 0.35 Hz to 90 kHz, +0/-3 dB |
| Noise | < -95 dBu, unweighted, 22 kHz measurement bandwidth |
| Dynamic Range | > 118dB, unweighted |
| THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), < 0.1% any amount of compression up to 40 dB, 1 kHz |
| IMD | < 0.1% SMPTE |
| Interchannel Crosstalk | < -80 dB 20Hz to 20 kHz |
| Stereo Coupling | True RMS Power Summing |
| Compressor Threshold Range | -40 dBu to +20 dBu |
| Compressor Ratio | 1:1 to infinity:1 |
| Compressor Threshold Characteristic | Selectable OverEasy® or hard knee |
| Compressor Attack/Release Characteristic | AutoDynamic™ |
| Compressor Attack/Release Modes | Selectable Manual or Auto |
| Compressor Manual Attack Time | Scalable program-dependent |
| Compressor Manual Release Time | Scalable program-dependent |
| Compressor Auto Attack Time | Program-dependent |
| Compressor Auto Release Time | Program-dependent |
| Compressor Output Gain | -20 to +20 dB |
| Limiter Threshold Range | +4 dBu to +24 dBu (off) |
| Limiter Ratio | infinity:1 |
| Limiter Type | PeakStopPlus® two-stage limiter |
| Limiter Stage 1 | PeakStop® brickwall limiter |
| Limiter Stage 1 Attack Time | Zero |
| Limiter Stage 1 Release Time | Zero |
| Limiter Stage 2 | Predictive intelligent program limiter |
| Limiter Stage 2 Attack Time | Program-dependent |
| Limiter Stage 2 Release Time | Program-dependent |
| Expander/Gate Threshold Range | Off to +15dBu |
| Expander/Gate Ratio | 1:1 to 30:1 |
| Expander/Gate Attack Time | < 100 µsec |
| Expander/Gate Release Time | Program-dependent |
| SC Ext. Switch | Routes the external sidechain input signal to the detector |
| SC Mon. Switch | Routes the sidechain signal to the output, interrupting the normal audio |
| OverEasy® Switch | Activates the OverEasy compression function |
| Countour Switch | Activates the frequency-dependent detector function |
| Auto Switch | Activates automatic program-dependent attack and release times, disabling the manual Attack and Release controls |
| I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter |
| Bypass Switch | Activates the direct input-to-output hard-wire relay bypass. Relay automatically hard-wire bypasses unit at power-down and provides a power-on delay of 1.5 sec. |
| Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneoulsy for both input and output levels |
| ST Link Switch | Link both channels for stereo operation. Channel One becomes the master |
| Gain Reduction Meter | 12-segment LED bar graph at 1, 2, 4, 6, 9, 12, 15, 18, 21, 24, 27 and 30 dB |
| I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu |
| Compressor Threshold Meter | 3-segment LED bar graph at Below (-), OverEasy and Above (+) |
| Expander/Gate Threshold Meter | 2-segment LED bar graph at Below (-) and Above (+) |
| Limiter Threshold Meter | 1 LED to indicate PeakStopPlus™ limiting |
| Function Switches | LED indicator for each front-panel switch |
| Output Transformer Options | Jensen® JT-123-dbx or JT-11-dbx, BCI RE-123-dbx or RE-11-dbx |
| Operating Voltage | 100-120 VAC 50/60 Hz 200-240 VAC 50/60 Hz |
| Power Consumption | 20 Watts |
| Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T |
| Power Connector | IEC receptacle |
| Dimensions | 1.75"Hx19"Wx9"D (4.4cmx48.3cmx20.1cm) |
| 设备重量 | 5.1 lbs. (2.3 kg) |
| Shipping Weight | 7.5 lbs. (3.4 kg) |
>Giá chưa bao gồm VAT
Địa Chỉ 1: 488 Trần Khát Chân, phường Phố Huế, Q. Hai Bà Trưng, Hà Nội
Điện thoại: 024 36 286 033 - 0902.188 .722 ( Mr Văn)
Địa Chỉ 2 : 365 Điện Biên Phủ, P4, Q.3, TP.HCM
Điện thoại: 0903.400.600 - 0909.37.34.74 ( Mr Sử)
